|
MUST BE DONE BEFORE GOING
TO THE TRACK ( RULES IS RULES ) |
|
TASK |
TASK STATUS |
| Install removable side bars on the roll cage |
Done -
Photo |
| Relocate drive shaft loop |
Done -
Photo |
| New cross member for the 700R4 transmission |
Done. We left the TH400 cross-member in for
possible future use. -
Photo |
| Install new rear gears ( 4.10 ),
bearings and seals |
Done |
| Install new drive shaft |
Done |
| Lower the seat |
Done |
| Fasten seat back to roll cage back bar |
Done |
| Add dual throttle springs |
Done |
| Wire neutral safety switch |
Done |
| Install transmission blanket |
Done |
| Install box around lower fuel cell |
Done -
Photo |
| Install new safety harness |
Done |
| Mount new front tires |
Done |
| Install new electrical panel |
Done -
Proud Photos |
| Installing new Lokar pedal and cable
assembly. Adjust for full throttle and correct TV cable
operation |
Done - Proud Photos |
| Nip off all the sheet metal screws
protruding into the rear wheel wells |
Done |
| Fabricate and install new alternator mount |
Done -Proud
Photo |
| Install roll cage padding |
Done |
| Install SFI approved damper |
Done |
| Install new rear shocks ( one shock has
locked up) |
Done |
| Re-mount radiator. Install Edelbrock water
pump and 18" fan |
Done - Proud Photo |
|
WOULD LIKE TO DO BEFORE
GOING TO THE TRACK |
|
TASK |
TASK STATUS |
| Install line lock |
Done - Photos
& Re-Do Photos |
| Install new carb and manifold |
Installed new motor -
ZZ502 |
| Install new air cleaner |
Done |
| New street slicks |
Done |
| Install tranny flexplate cover |
Done |
| Install wide band oxygen sensor and air/fuel
ratio digital display |
Done |
| Install rubber hood stop bumpers |
Done |
| Paint the roll cage |
Done |
| Install new front shocks - current shocks
are cheapo |
Done, QA1 adjustable -12 rebound settings |
| Adjust the trunk fitment - starting to bind
when opening. |
Done |
| Install dual channel playback tach |
Installed one channel recording tach. |
| Dyno tune ignition advance and carb |
|
|
REMAINING PROJECTS |
|
TASK |
TASK STATUS |
| Install glove box box |
Done |
| Add horse power ( cam and heads ) |
Installed new motor -
ZZ502 |
| Install temperature control to electric
radiator fan |
Done |
| Sell the bug catcher on eBay |
Done |
| Change the front springs to set the correct
attitude. |
Done for now |
| Install cowl hood scoop or fiberglass hood
with scoop |
Researching; scoop height requirement not
known until I install the air cleaner; |
| Clean and paint undercarriage and suspension |
Cleaning in process |
| Rewire some and generally clean up wiring |
Done - Installed new electrical panel -
PHOTOS |
| Paint job |
|
| New head liner |
Parts are in |
| New interior panels |
Front kick panels done. rear panels pending. |
| New carpeting |
|
| New seats |
|
| New dash / switch panel |
Done -
Proud Photos |
| Install fuel level sending unit |
Can't. The fuel cell is filled with foam. |
| Install data acquisition system |
Purchased an Altronics O2 Alert. The O2
Alert does data logging of engine RPM, O2, battery voltage
and three other external analog signals.
I'll design and build a signal processor board to
interface drive shaft RPM and either of EGT,
carburetor secondary butterfly position, engine oil
pressure, transmission oil pressure, water temperature,
manifold vacuum or whatever else I think I might need. |
| Add lightness ( fiberglass hood, trunk lid,
bumpers, fenders ) |
|
| Replace the 2x4 wood brace in the trunk with
an aluminum brace |
|
| |
|
